| 1956 Ford F-100 panel truck project |
Last updated on January 5, 2008 |
Our 1956 Ford panel truck project
I've always liked '56 Ford F-100 pickups and panel trucks. After keeping an eye out for an affordable, straight,
solid '56 F-100 panel truck project for many years, I grabbed this one as soon as I found it.
Here's how the truck looks now. This picture will be replaced whenever there's a significant change.
At the end of April, 2007, we brought the truck home and rolled it into the garage to finally start working on
it.
After going over them with paint stripper, a razor blade, and a D/A sander, the front fenders and the entire
outside of the body except for the roof are now in bare metal.
The condition of the body is amazing. There wasn't any
body filler anywhere on the truck. There are no dents
anywhere on it that are deeper than an eighth of an inch, and the amount of rust damage totals up to less than one
square inch. This truck is a survivor.
It turns out that one of the reasons the body of the truck is so well-preserved is because decades ago, it was
painted with a thick coat of house paint.
Here it is, shown as it was when I bought it, back on November 11, 2006.
For this picture, a pair of fenders and a hood from another truck were set in place without being bolted
down.
Here it is sitting on the
race car trailer, ready to pulled out of where it
had sat for decades.
At one time the truck had a roof rack bolted on, so each side of the roof has two pairs of eighth-inch holes that
will need to be filled. A pair of extra taillights had been mounted on the sides of the body, leaving a pair of
3/8-inch holes to be filled.
Other than that, the truck has never been butchered, hit, or rusted. The paint may be rough, but the body is
surprisingly straight. Realistically speaking, this is a great starting point.
When a '53-'56 Ford panel truck comes up for sale, it usually falls into one of two categories. Sometimes it will
be an old, worn-out work truck that has sat outside for most of its life and rusted-out. It's more common to be
something expensive that's been rebuilt and street-rodded with a lot of parts that you wouldn't have used, and a
paint job that hides the real condition of the sheet metal.
This '56 F-100 panel truck was built in San Jose, California. It left the factory with a 272-inch V-8, the
optional Custom Cab trim, and dark blue paint.
It has spent its whole life in Arizona, and was used as a plumber's shop truck.
On the inside, racks for shelves had been welded on each side. I took this picture before I carefully cut them out
and cleaned the inside with a pressure washer.
In the 1970s, a
hot rodder here in Phoenix bought it, cleaned the
frame, installed a
454 and a Turbo 400, and then pulled them out and set
the truck aside to work on other projects.
The rear pan is fairly straight and really solid.
The previous owner told me that in all the time he owned the truck, he had never opened the back doors because the
latches were frozen. I sprayed them with
Gibbs Brand to free them up. This picture was taken
after the back doors were opened for the first time in decades.
The rare, cherry '53-'56 panel truck rear bumper is fresh from the
chrome shop. In January I found a set of mounting
brackets for it.
This new old stock, chrome 1956 F-100 V-8 grille has never been on a truck.
It's shown with an original '56 V-8 emblem I cleaned up.
Mark Morton's '56 panel is a lot like what I want
to end up with. Shown above parked on the
Bonneville Salt Flats, Mark's panel has a
big block Chevy 427, and it runs great pulling a loaded
race car trailer on the highway.
For this one, I've already set aside a lot of parts, including a
healthy Chevy 454, several '57-64 Olds rear ends, a
set of NOS
1960s Stewart Warner gauges, some
neat old aluminum wheels, and an original
'56 F-100 axle that I've polished.
As work progresses on the panel project I'll keep adding current pictures of it here.
So far, I've only had time to work on the truck for a few afternoons. Since most of these pictures were taken,
I've cleaned the interior with a pressure washer, removed the racks from the inside, cleaned and detailed a lot of
small parts, and sanded the front fenders down to bare metal so they're ready to have a few dents removed. Sanding
the hood will come next.
At some point we're going to have to lift the body off the chassis so we can sandblast and box the frame.
After every part has been detailed and everything is assembled with the bare metal body protected by
Gibbs Brand, the truck will head to my friend
Cole Foster's shop in California for some minor
bodywork.
|
Chassis and running gear
Several years ago, having decided that I was going to build up a '56 panel when I found the right one, I bought
this original '56 F-100 axle. It's shown here partially polished with abrasives, ready to be
dropped three inches before final polishing.
When you're building classic F-100 into a hot rod truck, there are lots of choices when it comes to front ends.
Some people (especially people who sell parts for a living) will tell you that a good way to go is to scrap the
original front end and replace it with a custom-built front crossmember and the suspension out a Volare or a Dodge
Dakota, or even a Mustang II. Those conversions often add new problems.
Although this truck is going to look good and run well, it's always going to be a truck. That calls for a strong,
reliable front end that doesn't go out of alignment or sag, and something that parts will always be available
for.
After the chassis is stripped down, the frame rails will be boxed to minimize body flex. The '53-'56 F-100 panel
truck frames are essentially identical to the frames for the pickups, and when the pickups were designed, frame
flex was engineered into them to provide additional suspension travel.
Before painting the frame, I will design and fabricate a sturdy trailer hitch for pulling the
race car trailer.
|
This is one of several '57-'64 Olds rear ends I've bought, cleaned, and polished with abrasives.
These Olds rear ends are strong, they look great, and they're "period correct" for the
traditional hot rods and
race cars I like.
The '57-'64 Olds rear ends are no longer easy to find, and when they do show up, they're usually open rear ends
rather than the Oldsmobile "Anti-spin" or Pontiac "Safe-T-Track" limited-slip.
On eBay, a couple of days before I bought the truck, I had bought the rear axle housing and center section out of
a one-owner 1961 Oldsmobile. This car had 2.87 gears in an "Anti-spin" limited-slip center section that takes
31-spline axles. 2.87 is a taller ratio than I would have chosen, but a variety of new gears are available for it.
|
1956 Ford panel truck parts we need
Here are some of the pieces that I'm looking for:
1956 Ford F~100 pickup or panel truck parts:
Fenders
Gravel pan (behind the front bumper)
Inner fenders
Hood
1956 Ford F~100 panel truck parts:
Back door slides
If you have any of these parts for sale, please call Dave at (602) 233-8400. Thanks.
|
Classic Ford F-100 clubs and events
Classic Ford truck parts sources
More classic truck sites
All text and images on Roadsters.com are Copyright 1996-2008 Dave Mann
|